Get a Quote

wet ball mill fineness mining machines

wet grid ball mill - rhyther mining

wet grid ball mill - rhyther mining

Grid ball mill is widely used in smashing all kinds of ores and other materials, ore dressing and national economic departments like building and chemical industries etc. The size of ore shall not exceed 65mm and the best feed size is under 6mm. The effect in this job is better than coarse grinding. Grid ball mill consists of the shell, feeding part, discharging part, main bearing, lubricating system, driving system and other parts. There is wearing a liner inside the shell, and both ends of the shell are provided with a flange. The end cover of the mill is connected with the flange plate. The feeding part consists of the head, trunnion and feeding device. The discharge part includes the grid plate, head, and discharge trunnion.

Wet Grid ball mill is mainly used for mixing and grinding materials in two types: dry grinding and wet grinding .It has advantages of fineness uniformity and power saving. The machine uses different types of liner to meet different customer needs. The grinding fineness of material can be controlled by grinding time. The electro-hydraulic machine is auto-coupled and decompressed to reduce the starting current, and its structure is divided into integral type and independent type.

Compared with similar products,Wet Grid ball mill has the characteristics of low investment, low energy consumption, novel structure, simple operation, stable and reliable performance. It is suitable for mixing and grinding ordinary and special materials. The users can choose the right type, liner and medium type by considering the specific gravity, hardness, yield and other factors. The grinding medium is Wet Grid ball.

1.The ball mill is composed of a horizontal cylinder, a hollow shaft for feeding and discharging, and a grinding head. The main body is a long cylinder made of steel. The cylinder is provided with an abrasive body, and the steel lining plate is fixed to the cylinder body. The grinding body is generally a steel ball and is loaded into the cylinder according to different diameters and a certain proportion, and the grinding body can also be used with a steel section.

2.According to the particle size of the grinding material, the material is loaded into the cylinder by the hollow shaft of the wet grid ball mill feeding end. When the ball mill cylinder rotates, the grinding body acts on the cylinder liner due to the action of inertia and centrifugal force and friction. It is carried away by the cylinder. When it is brought to a certain height, it is thrown off due to its own gravity. The falling abrasive body crushes the material in the cylinder like a projectile.

3.The material is uniformly fed into the first chamber of the mill by the feeding device through the hollow shaft of the feeding material. The chamber has a step liner or a corrugated liner, and various steel balls are loaded therein. The rotation of the cylinder generates centrifugal force to bring the steel ball to a certain extent. The height drops and then hits and grinds the material. After the material reaches the rough grinding in the first bin, it enters the second bin through the single-layer partition plate. The bin is embedded with a flat liner with steel balls inside to further grind the material. The powder is discharged through the discharge raft to complete the grinding operation.

The main function of the steel ball in the ball mill is to impact crush the material and also play a certain grinding effect. Therefore, the purpose of grading steel balls is to meet the requirements of these two aspects. The quality of the crushing effect directly affects the grinding efficiency, and ultimately affects the output of the ball mill. Whether the crushing requirement can be achieved depends on whether the grading of the steel ball is reasonable, mainly including the size of the steel ball, the number of ball diameters, and the ball of various specifications. Proportion and so on.

The ball mill is composed of the main part such as a feeding part, a discharging part, a turning part, a transmission part (a reduction gear, a small transmission gear, a motor, and electric control). The hollow shaft is made of cast steel, the inner lining can be replaced, the rotary large gear is processed by casting hobbing, and the barrel is embedded with wear-resistant lining, which has good wear resistance. The machine runs smoothly and works reliably.

grinding - mineral processing

grinding - mineral processing

The final fineness of the product mainly depends on the number of times the ore particles pass through the grinder. The longer the grinding, the smaller the particle size. Separate crushing and grinding steps are necessary, the ball mill can only receive the broken ore particle, and then grind to the grinding fineness required for flotation.

In order to separate the concentrate from the ore, the ore should be ground fine enough to release the target mineral from the non-mineral grains. The degree of grinding required for this depends on the size of the mineral particles in the ore. A laboratory-scale flotation test is usually required on materials of different particle sizes to determine the grinding particle size required to release the target minerals.The fineness of the ore particles produced by grinding is crucial to recover the minerals by flotation. The most common grinding machines are semi-automatic (SAG) and automatic (AG) mills and ball mills.

Determining an optimal grinding size can maximize the recovery of target minerals in the subsequent flotation process.The grinding size is too large, and some ore particles and non-ore particles cannot be separated, thus preventing their flotation. If the particle size is too fine, the bubbles that rise during the flotation will push the very fine ore-containing particles away, preventing them from contacting the bubbles, thereby reducing their ability to be recovered into the concentrate.In addition, extremely fine rock and iron sulfide particles may agglomerate with extremely fine sulfide ore particles, preventing the ore particles from floating.

According to the test, the particles usually need to be ground to a diameter of about 100 mm to release minerals from each other. When the particles are less than about 10 mm, this is not conducive to the flotation effect.Grinding operations are very power-hungry, which is another reason to avoid excessive grinding.

The crushed products are ground in SAG or AG mills. The self-grinding machine can grind ore without grinding media such as iron ball, or steel rod, as long as the hardness of the ore is sufficient for the rolling ore to grind by itself.A large vibrating screen is used to sieve the ground products to separate the oversized particles. A small cone crusher to recover the oversized material, and then sent them return to the SAG or AG mill for re-grinding. The correct size material is sent to the ball mill for final grinding.

The ball mill is the fine grinding machine connect the SAG or AG mill and flotation machine. Ball mills produce fine particles with a uniform size for flotation, its grinding medias commonly are steel ball. The ball mill rolls grinding media together with the ore, as the ore grinds, these balls initially 5-10 cm in diameter but gradually wear out.Grinding is always carried out under wet conditions, with about 70% solid mixture in water.This procedure maximizes ore production and minimizes power consumption.

china wet mill for gold milling plant - china wet ball

china wet mill for gold milling plant - china wet ball

Wet Ball Mill, Gold Grinding Mill Machine, Wet Pan Mill manufacturer / supplier in China, offering Wet Mill for Gold Milling Plant, 2 Ton Auto Operation Dry Mortar Machine Dry Mortar Mixer, Chicken Manure Organic NPK Compound Fertilizer Making Machine Plant and so on.

Related News
Contact Us

Do you need to know the product price? model? Configuration scheme? Output? Please leave your correct message and we will reply you within 24 hours.

I accept the Data Protection Declaration